Ya, I'm not sure hence my post. Sounds like he turns it on and it works.

Sign up, and you can make all message times appear in your timezone. Sign up

Report problem with this ad

Nov 7, 2024
9:46:20pm

Rusty Crab Daddy All-American

Ya, I'm not sure hence my post. Sounds like he turns it on and it works.

Report problem with this ad

Rusty Crab Daddy

Previous username: IGotAverageGifs
Bio page: Rusty Crab Daddy
Joined: Mar 5, 2007
Last login: Nov 7, 2024
Total posts: 40,662 (10,598 FO)

Report problem with this ad

Messages

Author

Time

Furnace question

drdrcoug Redshirt Freshman

Nov 7, 9:39pm

RE: Furnace question

StantonMac

Nov 7, 9:41pm

My advice: Leave it flipped on.

Rusty Crab Daddy

Nov 7, 9:41pm

I have a thought but I have to leave the building before I'm locked in.. will check back when I'm home if no one chimes

timpjynx

Nov 7, 9:44pm

So if you flip the switch it runs successfully for a cycle but then fails after

tkh9

Nov 7, 9:45pm

Ya, I'm not sure hence my post. Sounds like he turns it on and it works.

Rusty Crab Daddy

Nov 7, 9:46pm

I thought your advice was solid.

tkh9

Nov 7, 9:48pm

Correct. Ignites. Full fan comes on. Runs for about 45 minutes or so.

drdrcoug

Nov 7, 9:55pm

RE: Furnace question

yovocoug

Nov 7, 9:47pm

Does your furnace have an impeller motor?

AggieWeekendCougar

Nov 7, 9:47pm

Maybe? It looks like there is a smaller motor that runs for a while before the main one kicks on.

drdrcoug

Nov 7, 9:59pm

Even when not starting properly, does that one kick on?

AggieWeekendCougar

Nov 7, 10:00pm

Yes. That one runs for 30 seconds or so every few minutes.

drdrcoug

Nov 7, 10:02pm

After it has been running for a minute or two, can you see or hear an ignition

AggieWeekendCougar

Nov 7, 10:05pm

Check your air filter. Make sure it’s clean.

Blue Print

Nov 7, 9:47pm

How long does it run after you get it to turn on? There is a small metal rod cal

BYUBuckeyeGoCougs

Nov 7, 9:48pm

I cleaned mine once every few weeks for years.

Crazy Joe Davola

Nov 7, 9:51pm

this is where I was going.. cleaned mine with sandpaper for a season or three before finally replacing it.

timpjynx

Nov 7, 10:45pm

My guess: one of your kids climbed into the attic where your HVAC is and flipped that switch thinking it was the light

SaturdaySpecialDay

Nov 7, 9:48pm

I think that the switch is there to make it easier to work on the unit without

Cheap Seats

Nov 7, 9:49pm

My whole house is full of “interesting electrical choices”

drdrcoug

Nov 7, 9:57pm

We have a switch by our furnace for this reason only, 1986 build Utah rambler

Nov 7, 10:58pm

Try cleaning the flame sensor, YouTube will show you how.

Provolone

Nov 7, 9:50pm

There should be a blinking LED on the control panel

dug

Nov 7, 11:03pm

Report problem with this ad

Posting on CougarBoard

In order to post, you will need to either sign up or log in.

Report problem with this ad